離心分離式空氣干燥機

◆企業產品顯著特點 Product features

※還具有保持穩定相符的撒氣負壓和露點

1.粘附塔之極高與直徑約經進行實驗沒想到精密儀器計算的，塔床摩擦阻力小，保持了解壓縮的氣體常溫、干燥劑5秒的接觸到周期，足夠原材料氣的露點規定。

2.30％的常溫、干澀劑加工余量，用以補償的常溫、干澀劑的物種多樣性受損，保證 常溫、干澀。

3.較大型吸附器，提高認識環流飽滿順利通過干熱劑層，減少溝流現像。

※粉碎氣量自然損耗超過14％

1.優良的機筒設計構思，保留100％的活性炭吸附能量，店鋪的能量應用在增強降解階段中，的降解氣溫差，提高了裝置的解吸技能，使用降解更徹底清除。

2.皮膚干燥和重復利用選用選擇性對流傳熱方法，濕氣流流下干的吸附物劑時效性果更佳。重復利用氣出口國含濕量操控在亞達到飽和形態形態，使消音器器及排氣管渠道無結霜現象之慮。

3.可只能根據低溫干燥機的程序運行裝載各種需求的調節凈化能力氣攝入量，提高認識凈化能力環流陸續安全，凈化能力水壓低至臨界點。

※粗糙劑采用生命周期長

1.適于的機筒尺寸規格，使氣體利用常溫、非常干燥劑層的氣速和事件保持穩定好的工作狀態，充分的切實發揮常溫、非常干燥劑的耐磨性。

2.有效的控制系統顯卡配置，在熱空氣進去機筒前，經除油解決實時清理掉熱空氣中內植物油成分物與重污染源破壞物，以防低溫干燥劑層受污染源破壞。

※儀器主要包括了刺激高的品質電動伸縮及全自動閥和靠得住的全電子為了滿足電子時代發展的需求，可程序語言序智能控制器，人機對戰操作界面友愛，全自動接連表示雙塔過量空氣系數，反復的壽命當場可編，生產日期快速設置10min。調節閥 平均壽命歷時50萬次的動作。

※鍋筒內壁上作冷熱鍍防腐處置，10年不脫漆。

※瑜伽動作最準、特性可靠、實際操作便利，布置不同框架。

※Bend it out on the same has the stable pressure and dew point

1. The height and diameter adsorption tower by the experimental results calculated precisely, tower, ensure the small resistance bed compressed gas desiccant 5 seconds contact time, meet the requirements of the finished product angry dew point.

2.30% of the surplus, desiccant used to compensate for the natural aging, ensure desiccant dry.

3. Large diffuser, ensure uniform through the desiccant air layer, eliminate channel flow phenomenon.

※Bend the gas loss less than 14% renewable

1. Excellent barrel design, save 100% of the adsorption quantity of heat, storage quantity of heat is used to increase the regeneration stage again angry temperature, improve equipment desorption ability, make renewable more thoroughly.

2. Dry and regeneration of the reverse convection scheme, wet air through the dry when the adsorbent best effect. Getting angry export moisture content control in the saturated state, the muffler and exhaust passage without concentrations of condensation.

3. According to the operation of the dryer load demand adjust dosage, ensure again angry for stability, regeneration renewable air pressure low to critical.

※Bend desiccant long service life

1. The right of barrel size, make the gas through the desiccant flow velocity and time of layer be the best, give full play to the desiccant performance.

2. The reasonable system configuration, in the air into the barrel, except by the efficient before oil processing timely removal in the air in content and heavy oil pollutant, avoid desiccant layer contamination.

※The equipment adopts bend novel high quality and pneumatic valve electric and advanced and reliable full electronic programmable controller, friendly interface, automatic continuous display of the twin towers, working cycle, the programmable factory set 10 min. The valve life for 500000 times action.

※Bend the cylinder body wall be cold galvanizing antirust processing, 10 years don't rust.

※Bend action, stable performance, accurate, easy operation and installation with no need of foundation.

◆主要的新技術產品參數 Main technical parameters